______________________________________________________________________

SECTION I - PRODUCT IDENTIFICATION AND EMERGENCY INFORMATION

______________________________________________________________________

PRODUCT NAME:  MVT10                              CHEMICAL NAME:  N/A

CHEMICAL FAMILY: Petroleum based oil    EMERGENCY PHONE:  617-227-1133

CAS NUMBER:  Mixture - N/A                      CAS NUMBER:  Mixture - N/A

______________________________________________________________________

SECTION II - INGREDIENTS

______________________________________________________________________

The precise composition of this mixture is proprietary information.  A more complete disclosure will be provided to a physician or nurse in the event of a medical emergency.  The following components are defined hazardous in accordance with 29 CFR 1910.1200:  None.

For additional information see Section III.

______________________________________________________________________

SECTION III - HEALTH INFORMATION AND PROTECTION

______________________________________________________________________

ROUTES OF OVEREXPOSURE/FIRST AID:

INHALATION:  If difficulty in breathing or irritation occurs, move victim to fresh air area.  If difficulty persists call a physician.

SKIN CONTACT:  In case of skin irritation, remove any contaminated clothing, wash skin and clothing thoroughly with soap and water.  If irritation persists call a physician.

EYE CONTACT:  If eye irritation occurs, or material is splashed into the eyes, flush with clean water for 15 minutes.  If irritation persists call a physician.

INGESTION:  In case of ingestion as accompanied by nausea, stomach cramps, lethargy or other throat or stomach irritation, don not induce vomiting.  Call a physician immediately.

______________________________________________________________________

TLV VALUE:  5 mg/ms as oil mist (OSHA-PEL)

NFPA RATING:  1-H/1-F/0-R

PERSONAL PROTECTION INFORMATION:  Use safety goggles when eye contact may occur.  Minimize breathing vapor, mist or fumes.  Avoid prolonged or repeated contact with skin.

MSDS MVT10
FIL-TECH

______________________________________________________________________

SECTION IV - FIRE AND EXPLOSION HAZARD

______________________________________________________________________

FLASHPOINT 'F/COC:  >260

FLAMMABLE LIMITS/LEL:  0.9          VEL:  7.0

AUTOIGNITION TEMPERATURE 'F: >450

______________________________________________________________________

EXTINGUISHING MEDIA:  Foam, dry chemical, carbon dioxide.

SPECIAL FIRE FIGHTING INSTRUCTIONS:  Wear self contained breathing apparatus in confined area.  Use water to cool fire exposed containers.

HAZARDOUS COMBUSTION  PRODUCTS:  Fumes, smoke, carbon monoxide, carbon dioxide, sulfur oxides.

______________________________________________________________________

SECTION V - SPILL CONTROL PROCEDURE

______________________________________________________________________

STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED:  Eliminate all sources of ignition.  SMALL SPILLS:  Soak up with absorbant material.  LARGE SPILLS: Dike and pump into drums.  Prevent material from entering drains, sewers or waterways.

WASTE DISPOSAL METHOD:  Dispose of in accordance with local, state and federal regulations.

______________________________________________________________________

SECTION VI - TYPICAL PHYSICAL AND CHEMICAL PROPERTIES

______________________________________________________________________

BOILING POINT 'F:  >450              SPECIFIC GRAVITY (H20=1):  <1.000

VAPOR PRESSURE (mm Hg)/20'C:  <0.01  SOLUBILITY IN WATER:  Nil

PERCENT VOLATILES:  Nil              VAPOR DENSITY (AIR=1):  >1

APPEARANCE:  amber oily liquid with mild odor

______________________________________________________________________

SECTION VII - REACTIVITY DATA

______________________________________________________________________

STABILITY/CONDITION TO AVOID INSTABILITY:  Product is highly stable.

HAZARDOUS POLYMERIZATION OCCUR:  Will not occur.

MATERIAL AND CONDITIONS TO AVOID INCOMPATIBILITY:  Avoid contact with strong oxidants such as liquid oxygen or chlorine.

HAZARDOUS DECOMPOSITION PRODUCTS:  Smoke, COx, SOx.

MSDS MVT10
FIL-TECH

______________________________________________________________________

SECTION VIII - TRANSPORT AND STORAGE

______________________________________________________________________

ELECTROSTATIC ACCUMULATION HAZARD:  Not applicable.

STORAGE TEMPERATURE, 'F:  Avoid storing above 120'.

SPECIAL PRECAUTIONS:  If product freezes, thaw completely and agitate.

______________________________________________________________________

SECTION IX - HAZARD CLASSIFICATION

______________________________________________________________________

U.S. DOT CLASSIFICATION:  Not applicable.

EPA HAZARDOUS SUBSTANCE:  None.

CARCINOGENIC:  Not listed per NTP, IARC monographs or OSHA.

______________________________________________________________________

SECTION X - SUPPLEMENTARY INFORMATION

______________________________________________________________________

Superfund Amendments and Reauthorization Act of 1986 (SARA) Title III requires submission of annual reports or release of toxic chemicals that appear in 40 CFR 372 (for SARA 313).  This information must be included in all MSDSs that are copied and distributed for this material.  Components present in ths product at a level which could require reporting under the statute are:

    CHEMICAL            CAS NUMBER        CONCENTRATIONS

      NONE

Physical data on this sheet are to be construed for the purpose of safety determination and reflect maximum and/or minimum limits that are not necessarily actual product specifications.

MVT10

Date revised:  12/10/90